Home

Home

Subcategories

  • Audi
    <p>The mileage stopper works on all AUDI cars manufactured from 2014 till present.</p> <p>Note: The device stops all VAG vehicles from counting the distance to the next oil change (the service counter is stopped).</p> <p></p> <h2>Installation </h2> <p>The device is installed behind the dashboard. Installation takes about 30 minutes and it's possible to do it on your own.</p> <p></p> <p>✔️ Uninstalling the device will not affect the mileage data (the mileage will not jump up).</p> <p></p> <h2>Activation</h2> <p>Mode 1 is activated by default immediately after installation. No need to activate the device.</p> <p></p> <p>Programs are switched successively: to switch a mode, you need to press and hold the "back" button on the left side of the steering wheel for 10 seconds.</p> <p></p> <p>On some VAG models you need to press the “OK” button on the right side of the steering wheel (looks like a small “wheel” switch), or the lower button “OK/Reset” button on the right wiper lever.</p> <p></p> <h3>MODES:</h3> <p>1—Speedometer works normally / 70% of mileage is filtered (e.g. 100 miles will be counted as 30).</p> <p>2—Speedometer works normally / 80% of mileage is filtered (e.g. 100 miles will be counted as 20).</p> <p>3—Turn OFF (everything comes back to normal).</p> <p></p> <p>Mode switching is confirmed by the flashing of a hazard light.</p> <p></p> <p>There is also a mode that allows you to completely stop the mileage, but the speedometer arrow will not work if it is used.</p>
  • BMW
    <h2>Mileage filter for BMW: information regarding the installation and operation.</h2> <p style="font-size:13px;font-weight:400;">The mileage filter for freezing mileage for BMW works on all models of the F, and G series. The devices stop the mileage counter completely or “filter” up to 90% of the mileage (depends on the car's Dashboard model, selected Mode, and ECU firmware).</p> <p style="font-size:13px;font-weight:400;">✔️ The installation of the filter on any BMW model is quite simple and you can do it yourself</p> <p style="font-size:13px;font-weight:400;">✔️ All electronic units will display the same mileage information</p> <p style="font-size:13px;font-weight:400;">✔️ Removing the mileage filter will not affect the data</p> <h3>ACTIVATION</h3> <p style="font-size:13px;font-weight:400;">Most of the kilometer blocker bmw come pre-activated upon the install. If you installed the device and mileage continues to go up, please refer to the "Modes" section below.</p> <h3>MODES</h3> <p style="font-size:13px;font-weight:400;">To switch a mode, press and hold the "BC" button on the left control lever either for 5 or 10 seconds. Modes are switched successively. Mode switching is confirmed by the flashing of a hazard light.</p> <p style="font-size:13px;font-weight:400;">1 — (for Dashboards 6WA and 6WB, 2010-2019): Speedometer works normally / Mileage is stopped completely.</p> <p style="font-size:13px;font-weight:400;"><b>NB:</b> This mode only works with vehicles BMW that are not updated with 2019 ECU firmware.</p> <p style="font-size:13px;font-weight:400;">2 — (for Dashboards 6WA and 6WB, 2010-2019): Speedometer works normally / Mileage is filtered at 90% (e.g. 100 miles will be counted as 10).</p> <p style="font-size:13px;font-weight:400;">3 — (for Dashboards S6U3A): Speedometer works at 50% (e.g. 100 MPH will be shown as 50) / <a href="https://mileagestopper.com/">Mileage is blocked</a> by 50% (e.g. 100 miles will be counted as 50).</p> <p style="font-size:13px;font-weight:400;">4 — (for Dashboards S6U3A): Speedometer works at 25% (e.g. 100 MPH will be shown as 25) / Mileage is filtered at 75% (e.g. 100 miles will be counted as 25).</p> <p style="font-size:13px;font-weight:400;">5 — (for Dashboards S6U3A): Speedometer works at 10% (e.g. 100 MPH will be shown as 10) / Mileage is filtered at 90% (e.g. 100 miles will be counted as 10).</p> <p style="font-size:13px;font-weight:400;">6 — (for Dashboards S6U3A): Speedometer does not work / Mileage is completely stopped.</p> <p style="font-size:13px;font-weight:400;">7 — Switch OFF (everything comes back to normal). </p> <p style="font-size:13px;font-weight:400;"><b>Where is the odometer reset button BMW? </b></p> <p style="font-size:13px;font-weight:400;">To reset the trip odometer use the BC button on the turn indicator lever. Short press the BC button to toggle between the different widgets and info displays till you see a journey data line. Long press the BC button on the tour indicator to reset the trip odometer / journey data.</p>
  • Ford
    <p>The mileage filter for Ford cars and how it works.</p> <p>— The mileage filter for freezing mileage on Ford cars works on all models from 2014 and onwards;</p> <p>— Installing the speed filter on any  model takes a minimum of 30 minutes;</p> <p>— You can do it on your own if you so prefer;</p> <p>— Removing the filter will not affect the current  data;</p> <p>— The speedometer arrow on all Ford cars works correctly after the mileage freezer is installed.</p>
  • Genesis
    <h2>Genesis: information regarding the installation and operation.</h2> <p>Mileage Stopper is a new approach to working with Genesis odometer data.</p> <p>Our mileage filters for Genesis works on all models manufactured from 2016 till present. The devices are very similar to those that are used on Hyundai cars, mainly because it’s basically is the same manufacturer.</p> <p>✔️ The device is installed behind the dashboard and the process usually takes about half and hour minutes. A help from a certified technician is recommended because of all the expensive leather and trims.</p> <p>✔️ Removing the filter will not affect the current mileage data.</p> <h3>ACTIVATION</h3> <p>Most of the devices come pre-activated upon the install. If you installed the mileage stopper for  Hyundai Genesis and mileage continues to go up, please refer to the "Modes" section below.</p> <h3>MODES</h3> <p>Stopping mileage on Genesis vehicles tend to depend on the Speedometer model and ECU firmware version. Thus, to complement each car model, we developed several Modes that are available with each device. Some modes may work best for your car, and some may not.</p> <p>1. 50/50 Mode. The speedometer works at 50% (e.g. 100 MPH will be shown as 50 MPH) — 50% of mileage is filtered (e.g. 100 miles will be counted as only 50 miles).</p> <p>2. 25/50 Mode. The speedometer works at 25% (e.g. 100 MPH will be shown as 25 MPH) — 75% of mileage is filtered (e.g. 100 miles will be counted as only 50 miles).</p> <p>3. 0/100. The speedometer will not work at all — 100% of mileage is filtered (e.g. 100 miles will be counted as 0).</p> <p>4. Turn OFF.</p>
  • Hyundai
    <p>The new approach to working with Hyundai odometer data. Mileage correction tool.</p> <p></p> <p><span>✔️ </span>The mileage filter for freezing mileage count on Hyundai cars works on all models from 2014 and onwards;</p> <p><span>✔️ </span>The Hyundai speed filter is installed via the dashboard and it takes about 30 minutes;</p> <p><span>✔️ </span>It can be done on your own if you prefer;</p> <p><span>✔️ </span>Removing the filter will not affect the current mileage data.</p> <p></p> <p>Observations</p> <p>On all Hyundai cars, the mileage that will be taken into account by the odometer will depend on the operative system of the speedometer arrow, so our device contains several programs:</p> <p>- While the speedometer needle is running at 50% - 50% of the completed path will be stopped;</p> <p>- While the speedometer needle is running at 25% - 75% of the completed path will be stopped;</p> <p>- The mileage will be fully frozen when the speedometer arrow is inactive;</p> <p>- Mode without filtering.</p> <p></p> <p>On Hyundai models from 2008 to 2015, the device can be installed via the OBD2 connector found on the car interior. When this connection is made, the speedometer arrow will not work, but the odometer data will be stopped.</p>
  • Jaguar
    <h2>Mileage filter for Jaguar: information regarding installation and operation.</h2> <p></p> <p>If you need to solve a problem - mileage correction for Jaguar, will help you. Our device to freeze the mileage on a Jaguar car.</p> <p>✔️ Our  Filter for freezing mileage on Jaguar vehicles works on all models manufactured from 2011 until the present.</p> <p>✔️ All electronic units (ECU) will display the same mileage info.</p> <h3>Installation</h3> <p>The device is installed behind the dashboard. Installation takes from 30 minutes, but it is still possible to do it on your own.</p> <p>✔️ Uninstalling the device will not affect the  data (the mileage will not jump up).</p> <h3>Activation and Controls</h3> <p>We tend to ship most of our devices pre-activated. No need to activate the filter. If you installed the device and mileage continues to go up, that means your item is not pre-activated.</p> <p>To control the mileage correction filter, quickly press the “Set/+” and then “−” button on the right side of the steering wheel. Successful activation/deactivation is confirmed by the flashing of a hazard light.</p> <h4>TROUBLESHOOTING:</h4> <p>Sometimes, on older models, you need to press and hold “RES” button for 5 or 10 seconds instead.</p> <h3>Modes</h3> <p>The device doesn't have any modes. The device is either On or Off.</p> <p>✔️ Speedometer works at 100% percent on all models.</p> <h4>Note:</h4> <p><a href="https://mileagestopper.com/content/9-faq">Installing the Mileage Stopper</a> stops oil change interval indicator on all Jaguar vehicles.</p> <p></p>
  • Jeep
    <p>The mileage filter for Jeep cars and how it works.</p> <p><span style="font-size:11px;">✔️</span><span style="font-size:11px;"> </span> The   filter for freezing mileage on Jeep cars works on all models from 2014 and onwards;</p> <p><span style="font-size:11px;">✔️</span><span style="font-size:11px;"> </span> Installing the speed filter on any Jeep model takes a minimum of 30 minutes;</p> <p><span style="font-size:11px;">✔️</span><span style="font-size:11px;"> </span> You can do it on your own if you so prefer;</p> <p><span style="font-size:11px;">✔️</span><span style="font-size:11px;"> </span> Removing the device will not affect the current  data;</p> <p><span style="font-size:11px;">✔️</span><span style="font-size:11px;"> </span> The speedometer arrow on all  cars works correctly after the mileage filter is installed.</p>
  • KIA
    <p>The simple solution for Freezing mileage counts on Kia.</p> <p><span>✔️ </span>The mileage filter for freezing mileage count on KIA works on all models from 2014 and onwards;</p> <p><span>✔️ </span>The speed mileage filter installation on your KIA is performed behind the dashboard and it takes between 20 to 30 minutes;</p> <p><span>✔️ </span>If you want, you can do it yourself;</p> <p><span>✔️ </span>Removing the filter will not affect the current mileage data.</p> <p></p> <p>Observations</p> <p></p> <p>On all KIA cars, the mileage that will be taken into account by the odometer will depend on the operative system of the speedometer arrow, so our device contains several programs:</p> <p>- While the speedometer needle is running at 50% - 50% of the completed path will be stopped;</p> <p>- While the speedometer needle is running at 25% - 75% of the completed path will be stopped;</p> <p>- The mileage will be fully frozen when the speedometer arrow is inactive;</p> <p>- Mode without filtering.</p> <p></p> <p>On KIA models from 2008 to 2015, the device works through the OBD2 connector found on the car interior. When this installation is made, the speedometer arrow will not work, but the odometer data will be stopped.</p> <p>This type of installation may cause a stability error. But it will disappear once the device is removed on KIA.</p>
  • Land Rover
    <h2>Mileage filter for Land Rover / Range Rover: information regarding installation and operation.</h2> <p>Is it possible to freeze the mileage on a Land Rover or Range Rover?</p> <p>✔️ Our Mileage Filter for <a href="https://mileagestopper.com/">freezing mileage</a> on Land Rover vehicles works on all models manufactured from 2011 until the present.</p> <h3>Installation</h3> <p>The device is installed behind the dashboard. Installation takes from 30 minutes, but it is still possible to do it on your own.</p> <p>✔️ Uninstalling the device will not affect the mileage data (the mileage will not jump up).</p> <h3>Activation and Controls</h3> <p>We tend to ship most of our devices pre-activated. No need to activate the device. If you installed the device and mileage continues to go up, that means your item is not pre-activated.</p> <p>To control the device, quickly press the “Set/+” and then “−” button on the right side of the steering wheel. Successful activation/deactivation is confirmed by the flashing of a hazard light.</p> <h4><strong>TROUBLESHOOTING:</strong></h4> <p>Sometimes, on older models, you need to press and hold “RES” button for 5 or 10 seconds instead.</p> <h3>Modes</h3> <p>There are no modes on the device. The device is either On or Off. </p> <p>✔️ Speedometer works at 100% percent on all models. </p> <h4>Note:</h4> <p>Installing the Mileage Stopper stops oil change interval indicator on all Land Rover vehicles.</p> <p></p>
  • Lexus
    <p>The Mileage Stopper devices for Lexus are unique for each model and thus are not interchangeable as with other car brands. We have devices for models manufactured from 2015 till the present (with very few exceptions). Generally speaking, freezing mileage on both Lexus and Toyota is a far better solution than simple mileage correction (please read on).</p> <p>✔️ Removing the filter will not affect the current mileage data.</p> <p>✔️ Duplicate mileage in ECU and all other engine modules will be stopped.</p> <p><b>Installation</b></p> <p>Mileage Stopper for Lexus is installed behind the dashboard.</p> <p>The installation process is straightforward and doesn't take a lot of time. But be extra careful in order not to leave any marks on the dashboard plastic trims.</p> <p>Also, for some reason Lexus use plastic bolts to hold the instrument panel. Treat them gently, so you could easily screw them back on looking good as new.</p> <p>For more detailed installation instructions Lexus <a href="https://mileagestopper.com/">odometer stopper</a>, please watch our videos.</p> <p><b>Activation</b></p> <p>To activate the device or switch a mode either press a “RES” button on the right side of the steering wheel or use the cruise control joystick on the right control lever.</p> <p>Successful mode switching is confirmed by an automatic “Door Unlocked” LED on the dashboard or by a sound signal.</p> <p><b>Modes</b></p> <p>There are 3 (three) modes total:</p> <p>Mode 1. Mileage is stopped for 100% </p> <p>Mode 2. 90% of mileage is filtered * </p> <p>Mode 3. Turn OFF. All comes back to normal. </p> <p>Modes can be switched while driving. </p> <p>Mode 2 (90%) is a specific program for all Lexus vehicles. Its main purpose is to spread the SRS module log data across the car’s mileage. SRS module is on Toyota vehicles keeps a log such data as high revs, the times when the ABS is triggered, and so on. The catch is that SRS log data is impossible to correct post-factum. But by using the Second Mode this data does not get stuck at the same odometer value and thus will not raise any suspicion if the ECU and SRS modules are scanned with special service equipment. </p> <p style="margin-bottom:14pt;"><b>Known issues </b><b>by Lexus mileage correction</b><b>:</b></p> <p style="margin-top:0pt;margin-bottom:14pt;"><span>- Instant fuel consumption is not supported.</span></p> <p style="margin-top:0pt;margin-bottom:14pt;"><span>- Average fuel consumption is displayed incorrectly. </span></p>
  • Mazda
    <h2>Mileage Stopper for Mazda: information regarding installation and operation.</h2> <p>✔️ All electronic units (ECU) will display the same mileage info.</p> <p>✔️ Uninstalling the device will not affect the  data (the mileage will not jump up).</p> <h3>Installation</h3> <p>The mileage filter for Mazda is installed behind the dashboard. Installation takes from 30 minutes, but it is still possible to do it on your own.</p> <h3>Activation and Controls</h3> <p>The filter is shipped pre-activated. No need to activate the device.</p> <h4>Modes</h4> <p>The stop filter for Mazda doesn't have any modes. The device is either On or Off.</p> <p>✔️ Speedometer works at 100% percent on all models.</p>
  • Mercedes-Benz
    <p>Mileage Stopper for Mercedes-Benz is installed behind the dashboard.</p> <p>The installation process is straightforward and doesn't take a lot of time.</p> <p>For installation instructions, please see our videos.</p> <p><b>ACTIVATION</b></p> <p>Activation is performed with regular buttons in the car's interior and does not require the output of any wires or installation of an additional button.</p> <p>Our device works on all Mercedes cars manufactured from 2012 to 2019.</p> <p>Series 164, 166, 205, 212, 447, 253, 222 — all these models work without any errors.</p> <p>There are two modes (switched successively): ON and OFF.</p> <p>Mode switching is confirmed by the flashing of a hazard light.</p> <p>To SWITCH a mode:</p> <p>Models:</p> <p>— all C-Class (205 series)</p> <p>— all S-Class (222 series)</p> <p>— all GLC-Class (253 series)</p> <p>— all Vito and V-Class (447 series)</p> <p>Press and hold the "Return" button on the left side of the steering wheel for 10 seconds.</p> <p>Models:</p> <p>— all GL-Class (164 series)</p> <p>— all ML-Class (166 series)</p> <p>— all B-Class (212 series)</p> <p>Press and hold the "Mute" button on the right side of the steering wheel for 10 seconds.</p> <p><strong>ATTENTION:</strong> Please don't try switching the mode while moving/driving. It may cause the speedometer to get stuck at the value of the mode switching. To solve this issue, please leave the car to rest for an hour or two so that the ECU could reset itself or try turning off the device.</p> <p><b>Known glitches and issues: </b></p> <p>- Blinking interior light (only on W222 and W217 models), but if you set it to the minimum, it will not be visible.</p> <p>- Actual mileage is recorded in ECU (Only on some diesel models).</p> <p></p> <p><b>Speedometer Calibration.</b></p> <p>Mercedes-Benz vehicles have different ECUs depending on its engine's model and power. Thus the speedometer could be a little off, showing slightly different (higher or lower) values from the actual speed. Therefore, the device has a function for the speedometer arrow calibration.</p> <p>To calibrate the speedometer, you need to press and hold the "Plus" button (on the right side of the steering wheel) for five seconds. After holding the button for five seconds, the speed will start to increase. Release the button when the desired value is reached. To decrease the speed, press and hold the "Minus" button. Repeat if necessary. </p> <p>Calibration should be performed on an empty road with as few traffic lights as possible. Use a GPS device (or any smartphone app) to verify actual speed. </p> <p><b>How do I check the mileage on my Mercedes?</b></p> <p>Find the “Up”, “Down” and “OK” buttons on the left side of the steering wheel. Click the Up. Press these buttons until you find the car’s odometer. To reset the trip odometer use the same buttons to scroll through the menus until you find find the trip odometer. Press and hold the “RES/Reset” button to reset the trip odometer.</p>
  • MINI
    <h2>Mileage Stopper for MINI: information regarding the installation and operation.</h2> <p>All MINI cars are similar to the BMW F-series in regards to electronic equipment, thus all these cars have a device similar to the BMW F-series;</p> <p>The mileage filter for MINI works on all models manufactured from 2015 till present. The devices stop the mileage counter completely or “filter” up to 90% of the mileage (depends on the car's Dashboard model, selected Mode, and ECU firmware). </p> <p>✔️ Installing the Mileage Stopper device on any MINI model is simple. If you want to, you can do it on your own.</p> <p>✔️ All electronic units (ECU included) will display the same mileage information;</p> <p>✔️ Removing the filter will not affect the current data.</p> <h3>ACTIVATION</h3> <p>Most of the devices come pre-activated upon the install. If you installed the device and mileage continues to go up, please refer to the "Modes" section below. </p> <h3>MODES </h3> <p>To switch a mode, press and hold the "BC" button on the left control lever either for 5 or 10 seconds. Modes are switched successively. Mode switching is confirmed by the flashing of a hazard light.</p> <p>1 — (for Dashboards 6WA and 6WB, 2010-2019): Speedometer works normally / Mileage is stopped completely.</p> <p>NB: This mode only works with vehicles that are not updated with 2019 ECU firmware. </p> <p>2 — (for Dashboards 6WA and 6WB, 2010-2019): Speedometer works normally / Mileage is filtered at 90% (e.g. 100 miles will be counted as 10).</p> <p>3 — (for Dashboards S6U3A): Speedometer works at 50% (e.g. 100 MPH will be shown as 50) / Mileage is filtered at 50% (e.g. 100 miles will be counted as 50).</p> <p>4 — (for Dashboards S6U3A): Speedometer works at 25% (e.g. 100 MPH will be shown as 25) / Mileage is filtered at 75% (e.g. 100 miles will be counted as 25).</p> <p>5 — (for Dashboards S6U3A): Speedometer works at 10% (e.g. 100 MPH will be shown as 10) / Mileage is filtered at 90% (e.g. 100 miles will be counted as 10).</p> <p>6 — (for Dashboards S6U3A): Speedometer does not work / Mileage is completely stopped.</p> <p>7 — Switch OFF (everything comes back to normal). </p>
  • Mitsubishi
    <h4>How to freeze the mileage count on Mitsubishi cars?</h4> <p></p> <p><span>✔️ </span>The mileage filter for freezing mileage count on Mitsubishi cars works on all models since 2017 and onward;</p> <p><span>✔️ </span>The installation of the mileage filter for any Mitsubishi model is performed behind the dashboard;</p> <p><span>✔️ </span>If you want, it can be done by yourself;</p> <p><span>✔️ </span>Removing the filter will not affect the current  data;</p> <p><span>✔️</span>The mileage count will be frozen on all blocks for all models.</p>
  • Porsche
    <p>The mileage filter on Porsche and How it works.</p> <p>✔️ The speedometer on all Porsche models manufactured after 2017 will work correctly after the freezing mileage is installed.</p> <p>Note: The device stops all Porsche vehicles from counting the distance to the next oil change (the service counter is stopped).</p> <h2>Installation</h2> <p>The device is installed behind the dashboard. Installation takes from 30 minutes to 1 hour depending on the trim, but it is still possible to do it on your own.</p> <p>✔️ Uninstalling the kilometer stopper for Porsche will not affect the mileage data (the mileage will not jump up).</p> <h2>Activation</h2> <p>The device is activated by default immediately after installation. No need to activate the device.</p> <p>There are no modes on the mileage freezer for Porsche. The device is either On or Off.</p> <p>To control the device, you need to press and hold the "back" button on the left side of the steering wheel for 10 seconds till the hazard light flashes once.</p>
  • SEAT
    <h3>How to freeze the mileage count on SEAT cars?</h3> <p>Buy and install Mileage filter to freeze mileage calculation on SEAT cars.</p> <p><span style="text-decoration:underline;">Activation devices for SEAT:</span> immediately after installing the device, Mode 1 is activated by default.The device “filters” up to 80% of the mileage or stops the mileage counter completely (depends on the mode selected). There are 5 modes, that are designed for different ECUs.</p> <p><span style="text-decoration:underline;">Modes:</span></p> <p>Mode 1—Speedometer works / 75% of mileage is filtered (e.g. 100 miles will be counted as 25).</p> <p>Mode 2—Speedometer works / 80% of mileage is filtered (e.g. 100 miles will be counted as 20).</p> <p>Mode 3—Speedometer does not work / 100% of mileage is filtered (e.g. 100 miles will be counted as 0).</p> <p>Mode 4—Turn OFF (everything comes back to normal).</p> <p>Modes are switched successively. To switch a mode, you need to press and hold the "back" button on the left side of the steering wheel for 10 seconds.</p> <p>On some VAG models SEAT you need to press the “OK” button on the right side of the steering wheel (looks like a small “wheel” switch), or the lower button “OK/Reset” button on the right wiper lever.Successful mode switching is confirmed by the flashing of a hazard light.</p> <p><span style="color:#000000;">Note:</span> the device stops all VAG vehicles from counting the distance to the next oil change (the service counter is stopped).</p>
  • Skoda
    <p>Activation stop kilometer Skoda: immediately after installing the device, Mode 1 is activated by default.</p> <p>The device “filters” up to 80% of the mileage or stops the mileage Skoda counter completely (depends on the mode selected). There are 5 modes, that are designed for different ECUs.</p> <p></p> <p>Modes:</p> <p>Mode 1—Speedometer works / 75% of mileage is filtered (e.g. 100 miles will be counted as 25).</p> <p>Mode 2—Speedometer works / 80% of mileage is filtered (e.g. 100 miles will be counted as 20).</p> <p>Mode 3—Speedometer does not work / 100% of mileage is filtered (e.g. 100 miles will be counted as 0).</p> <p>Mode 4—Turn OFF (everything comes back to normal).</p> <p></p> <p>Modes are switched successively. To switch a mode, you need to press and hold the "back" button on the left side of the steering wheel for 10 seconds.</p> <p>On some VAG models for Skoda you need to press the “OK” button on the right side of the steering wheel (looks like a small “wheel” switch), or the lower button “OK/Reset” button on the right wiper lever.</p> <p>Successful mode switching is confirmed by the flashing of a hazard light.</p> <p>Note: the device stops all VAG vehicles from counting the distance to the next oil change (the service counter is stopped).</p>
  • Toyota
    <p>The Mileage Stopper devices for Toyota are unique for each model and thus are not interchangeable as with other car brands. We have devices  odometer correction for models manufactured from 2015 till present. Generally speaking, freezing mileage on both Toyota and Lexus is a far better solution than simple mileage correction (please read on). </p> <p><span style="font-family:'Apple Color Emoji';">✔️</span><span style="line-height:normal;">  </span>Removing the filter will not affect the current mileage data.</p> <p><span style="line-height:normal;font-family:'Apple Color Emoji';">✔️</span> Duplicate mileage in ECU and all other engine modules will be stopped.</p> <p><strong>Installation devices for mileage correction for Toyota</strong></p> <p>Mileage Stopper for Toyota is installed behind the dashboard.</p> <p>The installation process is straightforward and doesn't take a lot of time. But be extra careful in order not to leave any marks on the dashboard plastic trims. </p> <p>Also, for some reason, both Toyota and Lexus use plastic bolts to hold the instrument panel. Treat them gently, so you could easily screw them back on looking good as new.</p> <p>For more detailed installation instructions, please watch our videos.</p> <p><strong>Activation</strong></p> <p>To activate the device or switch a mode either press a “RES” button on the right side of the steering wheel or use the cruise control joystick on the right control lever. </p> <p>Successful mode switching is confirmed by an automatic “Door Unlocked” LED on the dashboard or by a sound signal.  </p> <p><strong>Modes</strong></p> <p>There are 3 (three) modes total: </p> <p>Mode 1. Mileage is stopped for 100% </p> <p>Mode 2. 90% of mileage is filtered * </p> <p>Mode 3. Turn OFF. All comes back to normal. </p> <p><em>Modes can be switched while driving. </em></p> <ul><li>Mode 2 (90%) is a specific program for all Toyota vehicles. Its main purpose is to spread the SRS module log data across the car’s mileage. SRS module is on Tooyota vehicles keeps a log such data as high revs, the times when the ABS is triggered, and so on. The catch is that SRS log data is impossible to correct post-factum. But by using the Second Mode this data does not get stuck at the same odometer value and thus will not raise any suspicion if the ECU and SRS modules are scanned with special service equipment.   </li> </ul><p><strong>Known issues: </strong></p> <p>- Instant fuel consumption is not supported.</p> <p>- Average fuel consumption is displayed incorrectly.  </p>
  • Volkswagen
    <p>Programs are switched successively: to switch a mode, you need to press and hold the "back" button on the left side of the steering wheel for 10 seconds.</p> <p>On some VAG models Volkswagen you need to press the “OK” button on the right side of the steering wheel (looks like a small “wheel” switch), or the lower button “OK/Reset” button on the right wiper lever.</p> <h2><b>MODES:</b></h2> <p>1—Speedometer works normally / 70% of mileage is filtered (e.g. 100 miles will be counted as 30).</p> <p>2—Speedometer works normally / 80% of mileage is filtered (e.g. 100 miles will be counted as 20).</p> <p>3—Turn OFF (everything comes back to normal).</p> <p>Mode switching is confirmed by the flashing of a hazard light.</p> <h2><b>Activation: </b></h2> <p>Mode 1 is activated by default immediately after installation. No need to activate the device.</p> <h2><b>Installation:</b> </h2> <p>The device is installed behind the dashboard. Installation takes about 30 minutes and it's possible to do it on your own.</p> <p>Note: Removing the device will not affect the mileage data (the mileage will not jump up).</p> <p>Note: the device stops all VAG vehicles from counting the distance to the next oil change (the service counter is stopped).</p> <p>Our devices work on all Volkswagen cars manufactured from 2014 till present.</p>
  • OBD2
    <p>Mileage stopper works via connectors OBD2.</p>

There are 58 products.

Showing 1-50 of 58 item(s)
audi
Audi Q3 2018-2020 mileage filter
CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device. Mileage blocker device works on  Audi Q3 II (F3) 2018-2020. ✔️...
$249.00 Price
bmw
BMW X1 (F48, F49) Mileage Blocker
Mileage Blocker for BMW X1 (2015–2020) This device is compatible with the following models regardless of firmware version: F48, F49. Speedometer, cruise control and all other...
$209.00 Price
bmw
BMW X2 (F39) Mileage Blocker
Mileage Blocker for BMW X2 (2017–2020) This device is compatible with the following model regardless of firmware version: F39. Speedometer, cruise control and all other...
$209.00 Price
bmw
BMW X3 (F25) Mileage Blocker
Mileage Blocker for BMW X3 (2010–2017) This device is compatible with the following model regardless of firmware version: F25. Speedometer, cruise control and all other...
$209.00 Price
bmw
BMW X4 (F26) Mileage Blocker
Mileage Blocker for BMW X4 (2014–2018) This device is compatible with the following model regardless of firmware version: F26. Speedometer, cruise control and all other...
$209.00 Price
bmw
BMW i3 Mileage Blocker
Mileage Blocker for BMW i3 (2013–2020) This device is compatible with the model regardless of firmware version. Speedometer, cruise control and all other assistance systems work...
$209.00 Price
bmw
BMW i8 Mileage Blocker
Mileage Blocker for BMW i8 (2014–2020) This device is compatible with the model regardless of firmware version. Speedometer, cruise control and all other assistance systems work...
$209.00 Price
lexus
Lexus RX - Mileage freezer
CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device.Mileage stopper device works on Lexus RX. ✔️ Easy and fast...
$249.00 Price
lexus
Lexus NX - Mileage Stopper
CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device.Mileage stopper device works on Lexus NX. ✔️ Easy and fast...
$249.00 Price
lexus
Lexus LX - Odometer freezer
CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device.Mileage stopper device works on Lexus LX. ✔️ Easy and fast...
$249.00 Price
land-rover
Range Rover Sport II - Mileage Stopper
Mileage Stopper works as a digital CAN filter that allows to stop mileage counter. Mileage stopper device works on a Range Rover Sport II (2013–2017).  ✔️ Easy and fast...
$219.00 Price
toyota
Toyota Avalon
Mileage stopper for Toyota Avalon. CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device. ✔️ Connection Plug and play. ✔️ The...
$229.00 Price
toyota
Toyota Yaris
Mileage stopper for Toyota Yaris. CAN filter allowing to stop Mileage counting, mileage stopper works as CAN blocker, stop odometer device. ✔️ Connection Plug and play. ✔️...
$229.00 Price